If youre using an especially large toggle bolt, use a paddle bit to drill the hole. A paddle bit is designed to drill larger holes.
Use a sensor to detect electricity. A good stud finder will have the ability to detect electricity and metal. It may have a setting for metal studs and you can also use that setting as another precaution.
If you must hang your ceiling hook in a location where there is no joist, use a toggle bolt, also known as a toggle anchor, with a hook.
What hook or fitting would be best to hang net curtains for a window?
Assess the weight of the suspended item.
If the item you are using is less than five pounds, opt for an adhesive hook. Adhesive hooks also come in various sizes and are easy to remove without damaging the paint on your ceiling. (Note that adhesive hooks only stick on to flat ceilings, not textured ceilings.)
Estimating the weight of the item you want to hang from the ceiling will determine what size fastener you need. Hanging a paper lantern will require a different fastener than hanging a large, heavy pendant lamp.
You want to use a red head bolt. Youll drill the hole and as you tighten the sides, push out and lock it into place.
Use a pencil to mark the desired location of your hook screw once youve found a suitable joist.
How far from the wall/window do I hang a plant from the ceiling?
You can use an adhesive hook. Its easy to install and removable. But, you can only hook things that are only less than five pounds.
71% of people told us that this article helped them.
If the item is especially heavy, balance out its weight using two hook screws. Install the two screws at an angle from each other, not directly vertical.
There are various sizes of hook screws. If your item is small, use cup hooks or, even smaller, screw eye hooks.
Stop twisting once the base of the hook is flush with the ceiling. If you twist past this point, you could break the hook.
Ceiling joists are usually spaced either 16 or 24 inches (40.6 or 61.0 cm) apart from each other. Once youve located a joist, quickly find the next one by using a tape measure and measuring out either 16 or 24 inches (40.6 or 61.0 cm).
A stud finder is a handheld device that helps you identify where the studs in your wall and the beams in your ceiling are. They come in two main types: magnetic and electric. The magnetic ones detect where the studs are based on any metallic content in the stud (nails, etc.), these are very accurate, but can be difficult to use if the construction behind the drywall was done poorly. The electric stud finders sense changes in density, and are much more commonly used. They can identify the two outside edges of the stud, allowing you to pinpoint where it is. Most smartphones have apps to utilize their magnetic sensors as a magnetic stud finder.
Gently twist it clockwise; as it gets deeper, you will have to apply firmer pressure.
You can also knock on the ceiling with your knuckles. The areas between joists will produce a hollow, resonant sound, while the joists will produce a shorter, firmer sound.
Measure the thickness of the drywall and the weight of the item you want to hang; then consult a chart of load capacities to determine what size toggle bolt you should be using.
Inserting a hook into your ceiling is necessary for hanging plant baskets, paper lanterns, plug-in pendant lamps, and other suspended dcor. Hanging the hook incorrectly can lead to damage to your ceiling and the suspended item. Consult the steps below to learn how to hang a hook from a ceiling safely and securely.
The pilot hole should be slightly deeper than the length of the hook screws threaded shaft.
Thanks to all authors for creating a page that has been read 380,603 times.
My ceiling is concrete, what can I use for hanging a lamp from it?
When they reach the hollow space, the wings will open. Tightening the bolt will screw the wings down until they are secure against the inner surface of the ceiling.
How much weight can this hook hold?
Pinch the wings together and insert them through the hole.
Place the pointed tip of the hook screw into the hole.
How do i use a hook in a ceiling if hanging a plant?
Using a stud finder, select a hollow area in the drywall and mark it with a pencil.
Upload a picture for other readers to see.Upload errorAwesome picture! Tell us more about it?Click here to share your story.Article Info
The pilot hole will allow you to screw the hook screw into the ceiling by hand without it binding up or breaking.
If you have a crawl space or an attic with exposed joists, look to see which direction the joists are laid and also how far apart theyre spaced.
A ceiliing is usually made out of drywall and wooden beams. Unless you know your ceiling is different, get a drill bit made for wood, and make sure that it is a little bit smaller then the screw you plan on driving inside.
Wear safety goggles to avoid ceiling particles getting into your eyes.
Cookies make wikiHow better. By continuing to use our site, you agree to ourcookie policy.
If the packaging doesnt indicate the size, measure the base of the toggle when its closed to determine how big of a hole to drill.
Lay down plastic, tarp, or a sheet underneath the area where youll be drilling to keep your floor clean of debris.
A joist is one of the beams that supports a ceiling, and its the securest place to fasten a hook. The easiest way to locate your ceiling joists is by using a stud finder.
If youre hanging a lamp, make sure your hole is close to a power outlet that you easily can plug it into.
A toggle bolt cannot be screwed into a wooden joist, so make sure youre drilling into a hollow area.
Select a drill bit that is about the same diameter as your hook screws threaded shaft, but smaller than the outer threads themselves.
A toggle anchor with a hook consists of a bolt threaded through the center of two spring-loaded wings; a hook is attached to the end of the bolt instead of a standard bolt head.
Hook screws are small fasteners consisting of a pointed, threaded end and a curved hook end. They can be purchased from most hardware stores and will come in different sizes based on the amount of weight they can support.
If the hole is too wide, the thread of the screw wont have anything to grab onto.
Toggle bolt with hook (for drywall)
What kind of a drill bit do I need for this?
Español:colgar un gancho en un techoItaliano:Installare un Gancio Pendente dal Soffitto: Portugus:Instalar um Gancho em um TetoDeutsch:Einen Haken an der Decke befestigenFrançais:poser un crochet au plafondNederlands:Een haak in het plafond aanbrengen
The packaging on your toggle bolt should specify how big the hole should be – usually around half an inch.
What is a red head bolt that I need for ceiling hanging?
How can I do this without making a hole?
Include your email address to get a message when this question is answered.
Use an electric drill to drill a pilot hole into the ceiling joist.
Locate the nearest ceiling joist where you want to hang your hook.
If you have trouble twisting it through the last few rotations, grasp the hook gently with pliers and use the pliers to gain added torque.
If you dont have a stud finder, you could use a magnet to find nails in the ceiling joists.
Purchase a hook screw for your ceiling.
Drill a hole through the mark with an electric drill.
If youre looking to hang something heavier, opt for large utility storage hooks, which are strong enough to hold things like bicycles.
Never use a plastic anchor to hang something from a ceiling. Plastic anchors are meant to be used for lighter loads against a vertical wall.
How do I not drill into electric wiring?