How to Rewire a Hanging Lamp

How to Rewire a Hanging Lamp

Discard the old wire. Measure the old lamp socket and purchase a new one thats the same size.

Creatas Images/Creatas/Getty Images

Identify the neutral wire. The neutral wire should be indicated by markings or by a raised ridge. You can feel the ridges with your fingers. Wrap this wire clockwise around the silver-colored screw in your socket. The other wire without markings is the hot wire; wrap it clockwise around the brass-colored screw. Gently tighten both screws to hold the wires in place. The socket will rest against the inside of the globe holder.

visitReal Estate-Rentalsnavigation-www4

visitBusiness-Office Spacenavigation-www6

visitBusiness-Sponsored Contentnavigation-www5

visitA&E-Things To Donavigation-www14

visitHome-Site Indexnavigation-www11

visitTravel-Travel Albertanavigation-www10

Old House Online: How To Rewire an Antique Light Fixture

visitJobs-Get To Worknavigation-www4

visitSports-Collegenavigation-www12

Press the bare end of the neutral lamp wire to the bare end of the white wire in your ceiling. Screw them together with a wiring nut. Repeat with the hot wire and the black wire in the ceiling.

visitReal Estate-Place an adnavigation-www7

visitReal Estate-Mortgage Ratesnavigation-www5

visitSports-Sports Calendarnavigation-www9

visitHome-Newslettersnavigation-www12

visitHome-About SF Chronicle-SF Chronicle Staffnavigation-www2

visitSports-Outdoorsnavigation-www15

visitFood-Reservationsnavigation-www6

Replace the bulb and globe and turn your circuit breaker back on or replace the fuse. Test the new lamp by turning on the wall switch.

visitHome-Advertise with us-Media Kitnavigation-www2

visitA&E-The Daily Dishnavigation-www1

visitHome-Contact SFGate-Submissions & Tipsnavigation-www3

visitHome-About SFGate-SFGate Staffnavigation-www5

visitSports-Giants Fandomnavigation-www4

visitSports-Warriorsnavigation-www6

Take your hanging lamp apart. The designs of light fixtures vary depending on the age and style of the lamp, but a typical lamp will have a globe, a socket, a holder for the globe, tubing or chain to suspend the globe, and a canopy, which conceals the wires. At the end of the tubing or chain, you will most likely see a small, hollow piece of metal with threading inside. This is called a hickey and will hold the lamp to the ceiling. You should be able to take apart the entire lamp with a screwdriver. Keep track of all the parts and take photos of your progress if you think that you may have trouble putting it back together.

visitBusiness-Fossils & Photonsnavigation-www9

Note: Depending on which text editor youre pasting into, you might have to add the italics to the site name.

visitFood-Restaurantsnavigation-www1

visitHome-Your CA Privacy Rightsnavigation-www9

Remove the current fixture. Again, the exact design of your fixture will vary somewhat. Remove the bulb and globe first, then unscrew the canopy. Unscrew the wire nuts to disconnect the wires between the old fixture and the ceiling. You may need someone to hold the current fixture, as its unsafe to let it hang from the wiring.

visitReal Estate-Homesalesnavigation-www9

visitHome-Advertise with us-Public Noticesnavigation-www5

Lowes: How to Change a Light Fixture

visitJobs-Job Eventsnavigation-www1

visitLiving-Home & Gardennavigation-www1

visitNews-Obituariesnavigation-www8

Turn the overhead light where you will install the lamp off using the switch on the wall. Then turn off the electricity to the overhead light off by turning off your circuit breaker or removing a fuse, depending upon your situation. This is extremely important; you may injure yourself if there is any electricity running to the overhead light. Use a circuit tester to ensure that there are no live wires.

Thread the other end of the wire through your globe holder, chain or tubing and canopy, which will be attached to the ceiling. Screw the hickey onto the end of your chain or tubing, but dont thread the wire through it. Dont attach the globe yet. The canopy should be loose on the chain or tube.

Leggett, Rochelle. How to Rewire a Hanging Lamp.

visitHome-About SFGate-Register on SFGatenavigation-www3

visitSports-Sports Blogsnavigation-www8

visitHome-About SFGate-SFGate Newslettersnavigation-www4

visitReal Estate-Home Guidesnavigation-www8

visitHome-About SFGate-Careersnavigation-www6

Strip about an inch of the casing material from both ends of an 18-gauge strand of lamp wire. Lamp wire is composed of two wires that are side-by-side: a neutral wire and a hot wire. Measure down several inches from where you stripped the wire on either end, then split the wire down the middle to this point on both ends. Leave the casing intact along the split.

Antique Lamp Supply: Pendant Lamp Part Index

visitHome-Contact SFGate-Customer Supportnavigation-

Attach the canopy to the ceiling. Typically, you will attach the canopy to the strap with screws or secure it in place by tightening a locknut that is located below the canopy.

visitA&E-Music & Nightlifenavigation-www3

visitReal Estate-On the Block Blognavigation-www10

visitHome-About SF Chronicle-Manage Your Subscriptionnavigation-www4

visitTravel-Destination BCnavigation-www9

visitTravel-Wine Countrynavigation-www3

visitNews-News Blogsnavigation-www13

visitHome-Advertise with us-Place a Classified Adnavigation-www3

visitA&E-Performancenavigation-www4

What Is the Red Wire for When Installing a Light Fixture?

visitHome-About SF Chronicle-Back Copiesnavigation-www7

visitLiving-Sponsorednavigation-www10

Kight Home Center: Installing Wall & Ceiling Fixtures

visitBusiness-Home Guidesnavigation-www3

Leggett, Rochelle. (n.d.). How to Rewire a Hanging Lamp.

visitNews-Educationnavigation-www11

visitReal Estate-New Homesnavigation-www1

visitBusiness-Mortgage Ratesnavigation-www2

visitJobs-Salary Wizardnavigation-www3

visitFood-Top 100 Restaurantsnavigation-www3

Check with your local building codes to find out if there are any extra steps that you should take when rewiring a hanging lamp.

visitHome-Gate Listnavigation-www14

visitTravel-Weekend Getawaysnavigation-www1

visitBusiness-Technologynavigation-www1

visitHome-Advertise with us-About Our Adsnavigation-www4

This Old House: Everything You Need to Rewire a Light Fixture

visitHome-Advertise with us-Local Business Directorynavigation-www6

visitHome-Classifiedsnavigation-www2

visitFood-Top 100 Winesnavigation-www4

visitHome-About SF Chronicle-Chron in Educationnavigation-www8

visitTravel-Monterey-Carmelnavigation-www4

visitHome-Terms of Usenavigation-www10

visitFood-Bargain Bitesnavigation-www5

visitCars-Click and Clacknavigation-www2

visitHome-Get news alertsnavigation-www13

Install a Light Fixture With Two Lead Wires

visitFood-Inside Scoop SFnavigation-www7

Replacing a ceiling lamp or light fixture with an older lamp is a good way to instantly add a vintage or antique feel to a room. Older lamps often cost less than new ones, as well. Unfortunately, the wires in an older lamp can present a fire hazard. With a few tools, you can rewire a hanging lamp and install it yourself. For a simple single light, rewiring a lamp is not difficult, as long as you take all proper safety precautions.

A simple hanging lamp is not complex.

visitHome-About SF Chronicle-Become a Subscribernavigation-www3

visitCars-Sell Your Carnavigation-www5

visitBusiness-Mind Your Businessnavigation-www10

visitHome-Privacy policy-Ad Choicesnavigation-www2

Hang a Light Fixture When Fixture Wires Are Not Color Coded

Measure the entire length of your lamp, including any chain or tubing. Your wire must be at least six inches longer than this measurement. You can cut excess wire off when youre finished, but a wire that is too short will be difficult to work with.

visitReal Estate-Commercialnavigation-www6

visitHome-About SF Chronicle-E-Editionnavigation-www6

Unscrew a Socket From an Old Floor Lamp

visitBusiness-Public Noticesnavigation-www4

visitBusiness-The Tech Chroniclesnavigation-www7

visitNews-Bay Area & Statenavigation-www1

visitReal Estate-Open Homesnavigation-www2

visitLiving-Schools, Camps & Activitiesnavigation-www11

visitBusiness-Net Worth Plusnavigation-www8

visitHome-About SF Chronicle-SF Chronicle Deliverynavigation-www5

visitFood-Healthy Eatingnavigation-www8

visitHome-About SF Chronicle-Correctionsnavigation-www9

visitReal Estate-Luxurynavigation-www3

Examine the outlet box. There should be a metal strap across the box. This holds the fixture to the ceiling. Typically, you will see a threaded piece of metal protruding from the middle. Screw the hickey onto this piece. The socket, globe holder and rod or chain will be attached securely to the ceiling at this point.

Urban Cholita: Tutorial: How to Rewire a Lamp

visitLiving-Outdoorsnavigation-www8

Leggett, Rochelle. How to Rewire a Hanging Lamp accessed May 25, 2018.

Can You Use an Extension Cord Wire to Rewire a Lamp?

visitHome-About SFGate-FAQnavigation-www2

visitHome-About SFGate-Hearstnavigation-www7

visitTravel-Neighborhoodsnavigation-www2

Leave a Comment